Home > Flowmeters > Paddle Wheel Flowmeters > Insertion Flowmeter with Paddle Wheel
The flowmeter with paddle wheel for continuous flow measurement is especially designed for use in neutral, slightly aggressive, solid free liquids.
The Bürkert designed fitting system ensures simple installation of the devices into all pipes from DN 20…DN 400.
The flowmeter produces a frequency pulse signal, proportional to the flow rate, which can easily be transmitted and processed by a Bürkert transmitter/controller.
| Spec | Value |
|---|---|
Non wetted parts |
|
| Housing | PE |
| Union Nut | PC |
| Seals | NBR |
| Screws | Stainless steel |
| Female cable plug/male fixed plug | PA |
Wetted parts |
|
| Seal | FKM standard (EPDM option) |
| Axis and bearings | Ceramics (Al2O3) |
| Sensor armature, paddle wheel | PVDF |
| Dimensions | Detailed information can be found in chapter “4. Dimensions” on page 6 |
| Measuring principle | Paddle wheel |
| Compatibility | Any pipe from DN 20.)…DN 400 which is fitted with Bürkert S020 Insertion fitting. For the selection of the nominal diameter of the Insertion fittings, see data sheet Type S020 |
| Pipe diameter | DN 20…DN 400 |
| Measuring range |
|
Insertion Flowmeter Performance data |
|
| Measurement deviation | Teach-In: ± 1 % of the measured value.) (at Teach-In flow rate value) Standard K-factor: ± 2.5 % of the measured value.) |
| Linearity | ± 0.5 % of full scale |
| Repeatability | ± 0.4 % of the measured value |
Electrical Data |
|
| Operating voltage |
|
| Power source (not supplied) | Limited power source according to UL/EN 60950-1 standards or limited energy circuit according to UL/EN 61010-1 §9.4 |
| DC reverse polarity protection | Yes |
| Overvoltage protection | Yes |
| Current consumption | With sensor
|
| Outputs |
|
| Voltage supply cable | Max. 50 m length, shielded Cross section of wires: max. 1.5 mm² |
The flowmeter with paddle wheel for continuous flow measurement is especially designed for use in neutral, slightly aggressive, solid free liquids.
The Bürkert designed fitting system ensures simple installation of the devices into all pipes from DN 20…DN 400.
The flowmeter produces a frequency pulse signal, proportional to the flow rate, which can easily be transmitted and processed by a Bürkert transmitter/controller.
| Spec | Value |
|---|---|
Non wetted parts |
|
| Housing | PE |
| Union Nut | PC |
| Seals | NBR |
| Screws | Stainless steel |
| Female cable plug/male fixed plug | PA |
Wetted parts |
|
| Seal | FKM standard (EPDM option) |
| Axis and bearings | Ceramics (Al2O3) |
| Sensor armature, paddle wheel | PVDF |
| Dimensions | Detailed information can be found in chapter “4. Dimensions” on page 6 |
| Measuring principle | Paddle wheel |
| Compatibility | Any pipe from DN 20.)…DN 400 which is fitted with Bürkert S020 Insertion fitting. For the selection of the nominal diameter of the Insertion fittings, see data sheet Type S020 |
| Pipe diameter | DN 20…DN 400 |
| Measuring range |
|
Insertion Flowmeter Performance data |
|
| Measurement deviation | Teach-In: ± 1 % of the measured value.) (at Teach-In flow rate value) Standard K-factor: ± 2.5 % of the measured value.) |
| Linearity | ± 0.5 % of full scale |
| Repeatability | ± 0.4 % of the measured value |
Electrical Data |
|
| Operating voltage |
|
| Power source (not supplied) | Limited power source according to UL/EN 60950-1 standards or limited energy circuit according to UL/EN 61010-1 §9.4 |
| DC reverse polarity protection | Yes |
| Overvoltage protection | Yes |
| Current consumption | With sensor
|
| Outputs |
|
| Voltage supply cable | Max. 50 m length, shielded Cross section of wires: max. 1.5 mm² |
WJF Instrumentation Ltd.
#5 3610 – 29th Street N.E.
Calgary, Alberta
Canada
T1Y 5Z7
Calgary Head Office
Toll-Free: (877) 291-5572
Standard: (403) 291-5570
Ontario & Maritimes Sales:
Toll-Free (877) 291-5572
