Home > Chemical Feed Pumps > FMI OEM Pumps > Metering Pump Stepper Controller
The ICST-02 Intelligent Metering Pump Stepper Controller provides control of FMI’s STH and STQ metering pump family. The drive can be configured at the factory for either pump to deliver the most efficient performance necessary to control the pump over a wide speed range.
By properly configuring FMI’s ICST02 controller one can increase the performance efficiency
of a connected pump over a wide range of speeds. This PDF will describe the individual
connections on the controller, their electrical specifications, and their functions.
| Spec | Value |
|---|---|
| Dimensions: | 2.0″ x 3.1″ x 1.6″ high (51 x 79 x 41 mm) |
| Min. | Typ. | Max. | Units | ||
| Supply Voltage | Nominal Values | 7 | 36 | VDC | |
| Absolute maximum values, drive operating but outside guarantee parameters. | 4.9 | 42 | VDC | ||
| Absolute maximum values, surge (duration ≤ 10ms) |
-1 | +45 | V | ||
| Supply Current | +VLOG = 7V | 120 | 300 | mA | |
| +VLOG = 12V | 80 | 200 | |||
| +VLOG = 24V | 50 | 125 | |||
| +VLOG = 40V | 40 | 100 |
| Min. | Typ. | Max. | Units | ||
| Supply Voltage | Nominal Value | 9 | 36 | VDC | |
| Absolute maximum values, drive operating but outside guaranteed parameters | 8.5 | 40 | VDC | ||
| Absolute maximum values, surge (duration ≤ 10ms) |
-1 | +45 | V |
Settings in this tab (See Below) facilitate defining motion profiles using up to 10 phases of customized motor operations. This should assist in creating complex scenarios that may be required when operating an attached pump.
The user can choose to operate a specific phase or all selected phases up to 10 phases of operation. In each phase user can define motion parameters of interest, and if the pump should be Homed before selected phase starts. Also, user is allowed to force all selected phases to cycle indefinitely until stopped, also configure a delay period that takes effect before next cycle starts. FMI Configuration Tool automatically restores all Custom Program Settings that was used in previous execution of the application. Using “Load Custom Settings Parameters” and “Save Custom Settings Parameters” (See Below), Configured Program Settings can be stored and restored for future use for controlling the metering pump stepper controller.
The ICST-02 Intelligent Metering Pump Stepper Controller provides control of FMI’s STH and STQ metering pump family. The drive can be configured at the factory for either pump to deliver the most efficient performance necessary to control the pump over a wide speed range.
By properly configuring FMI’s ICST02 controller one can increase the performance efficiency
of a connected pump over a wide range of speeds. This PDF will describe the individual
connections on the controller, their electrical specifications, and their functions.
| Spec | Value |
|---|---|
| Dimensions: | 2.0″ x 3.1″ x 1.6″ high (51 x 79 x 41 mm) |
| Min. | Typ. | Max. | Units | ||
| Supply Voltage | Nominal Values | 7 | 36 | VDC | |
| Absolute maximum values, drive operating but outside guarantee parameters. | 4.9 | 42 | VDC | ||
| Absolute maximum values, surge (duration ≤ 10ms) |
-1 | +45 | V | ||
| Supply Current | +VLOG = 7V | 120 | 300 | mA | |
| +VLOG = 12V | 80 | 200 | |||
| +VLOG = 24V | 50 | 125 | |||
| +VLOG = 40V | 40 | 100 |
| Min. | Typ. | Max. | Units | ||
| Supply Voltage | Nominal Value | 9 | 36 | VDC | |
| Absolute maximum values, drive operating but outside guaranteed parameters | 8.5 | 40 | VDC | ||
| Absolute maximum values, surge (duration ≤ 10ms) |
-1 | +45 | V |
Settings in this tab (See Below) facilitate defining motion profiles using up to 10 phases of customized motor operations. This should assist in creating complex scenarios that may be required when operating an attached pump.
The user can choose to operate a specific phase or all selected phases up to 10 phases of operation. In each phase user can define motion parameters of interest, and if the pump should be Homed before selected phase starts. Also, user is allowed to force all selected phases to cycle indefinitely until stopped, also configure a delay period that takes effect before next cycle starts. FMI Configuration Tool automatically restores all Custom Program Settings that was used in previous execution of the application. Using “Load Custom Settings Parameters” and “Save Custom Settings Parameters” (See Below), Configured Program Settings can be stored and restored for future use for controlling the metering pump stepper controller.
WJF Instrumentation Ltd.
#5 3610 – 29th Street N.E.
Calgary, Alberta
Canada
T1Y 5Z7
Calgary Head Office
Toll-Free: (877)291-5572
Standard: (403)291-5570
Ontario & Maritimes Sales:
(905)809-6918
