Level Transmitters & Instrumentation

Burkert, Kobold, Intempco & B/W Controls

A large selection of Fluid Level Transmitters & Instrumentation available for shipping from our location in Calgary, Alberta, Canada.

Ultrasonic Level Transmitters

We stock a large selection of Level Transmitters & Instrumentation available for shipping from our location in Calgary, Alberta, Canada.

Below represents a small selection of more popular Fluid Level Instrumentation.

Contact us for advice and consultation regarding Fluid Level configuration and our expert staff can help you.

Simple Float Switch Level Instrument

Float switch with hermetically sealed reed contacts in a fixed switch part, switching triggered by magnets in floating switch part, reed contact implemented as alternator or normally open/closed; for neutral and aggressive liquids; not sensitive to dirt particles in the medium; cylindrical threading for simple installation in side of container.Different versions are available depending on material (PP or stainless steel), mounting position (horizontal or vertical) and equipment (relay).

  • Switch for neutral and aggressive liquids
  • NO/NC, alternating
  • Reed contact
  • Vertical or horizontal mounting
  • Molded lying leads (Type 8181) or cable (Type TCL001)

Call 1-877 291 5572 for Level Instrumentation consultation and configuration questions.

Float Level Instrument

Ultrasonic Level Measuring Device – Level Transmitters Type 8177

The type 8177 is a non-contact ultrasonic level measuring device, designed for continuous level measurement in open or closed vessels. The unit is suitable for liquids, but also for solids, in virtually all industries, particularly in water and waste water management.

  • For level measurement up to 8 m
  • 4…20 mA/HART – 2 wires
  • Suitable for solids
  • ATEX certification

Measuring principle

The transducer of the ultrasonic measuring device emits short ultrasonic pulses,at 55 kHz to the measured product. These pulses are reflected by the medium surface and received by the transducer as echoes. The running time of the ultrasonic pulses from emission to reception is proportional to the distance and hence to the level. An integrated temperature sensor detects the temperature in the vessel and compensates the influence of temperature on the signal running time.The determined level is converted into an outputsignal and transmitted as a measured value.

Call 1-877 291 5572 for Level Instrumentation consultation and configuration questions.

Ultrasonic Level Transmitters

LTX01 Level Sensor Continuous Capacitance Level Transmitters 4-20 mA, Loop Powered

INTEMPCO LTX01 series 2-wire level transmitters are highly reliable microprocessor based sensors designed to measure tank levels of liquids and certain dry bulk media in metal tanks. LTX01 sensors measure the change in capacitance that occurs as the tank level changes and outputs a standard loop-powered 4-20mA signal.

  • Continuous loop powered 4-20mA operation
  • Microprocessor Based
  • Accuracy 1% of span for constant dielectric of material
  • Non-interactive zero and span calibration
  • Calibration accomplished with 4 push buttons
  • Heavy duty industrial design
  • NEMA rated aluminum, stainless, PVC and explosion proof housings available
  • Standard fitting 3/4” NPT, flange and special fittings available

After calibration any change in level is recognized and converted to an analog 4-20mA signal. LTX01 sensors use very high frequency and very low amplitude sensing circuitry to greatly minimize the effects of coating on the sensing probe.The LTX01 includes a standard 4-20mA loop powered LTX transmitter housed in a rugged enclosure, a 0.50 inch diameter rigid probe for ranges up to 20 feet and a fitting.Probe material is SS316, supplied bare or PFA jacketed.The LTX01 is designed for tanks which have fitting connections of 3/4 NPT or larger.LTX01 can be used in many tough industrial applications.This level sensor is shock resistant and very rugged. There are no moving parts. PFA jacketed probe can withstand temperatures of up to 200°C and pressures to 500 psi

  • Water and water-based liquids.
  • Jacketed probes required for conductive media
  • Organic Acids
  • Oils and fuels in some metallic tanks
  • Use bare probes with non-conductive media
  • Use cable probes where top side access is limited
  • On-site calibration required
  • Not recommended where material dielectric changes
  • Tank must be conducive or grounding may be required or see other Intempco level probe.

Call 1-877 291 5572 for Level Instrumentation consultation and configuration questions.

Capacitance Level Transmitters