Home > Temperature > Back Mount Digital Temperature Gauge
The DTG07 series Digital Temperature Gauges are a complete solution for most industrial temperature monitoring and temperature indicating applications.
Of high quality construction, these gauges features a bright and large 4-digit red LED display with an analog 4-20 mA output.
Based on Intempco’s patented MIST™ technology, they are designed for optimum accuracy and performance.
| Sensing Element | RTD, Type Pt100 Class A |
| Temperature Ranges | Customer re-scalable between –200 o C to 600 o C or –50 o C to 200 o C depending model. No re-calibration required. |
| Switching Ranges | Customer programmable between –200 o C to 600 o C or –50 o C to 200 o C depending model. |
| Hysteresis | Customer programmable, 1% of range by factory setting. |
| Accuracy | ± ( 0.25 o C + 0.40 % of reading ) max. with default calibration. ± ( 0.10 o C + 0.20 % of reading ) max. with one-point factory or customer calibration. |
| Open circuit detection | Upscale ( 22 mA ) or Downscale ( 2.5 mA ) current output. Error message on LED display. |
| Warm-up | 30 seconds. |
| Response Time | 0.5 sec to 30 sec ( software selectable ) |
| Display | 4-DIGITS LED, decimal point selectable by software. |
| Display resolution | ± 0.02 % F.S. ±1 DIGIT |
| RFI effect | 1 % or less typical |
| Temp. Effect | < 0.01 % FS/ o C |
| Ambient Temp. Range | – 40 o C to 80 o C ( -40 o F to 176 o F ) |
| Storage Temp. Range | – 50 o C to 85 o C ( -58 o F to 185 o F ) |
| Max. Pressure | 500 PSIG ( on probe ) |
| Housing Material | Stainless steel 316 |
| Probe Material | Stainless steel 316 standard |
| Cable Materials | PVC, Teflon®, Silicone, SS armored Teflon® |
| Environmental Protection | NEMA 4/IP 65 |
| ELE CTRICAL | |
| Power Supply | 9-36 VDC, polarity protected |
| Supply effect | 0.005 %/V |
| Power consumption | 15 mA @ 24 VDC + output current – 950 mW max. 20 mA @ 24 VDC for PNP output – 500 mW max. 20 mA @ 24 VDC + sourcing current for NPN output 50 mA @ 24 VDC for Relay Output – 1200 mW max. |
| Current Output | 4-20 mA (3 wires configuration) linear to temperature. |
| Max load on current output | ( Vsupply-9V )/ 20 mA, Ohms |
| Switching Output | Transistor NPN ( max 100 mA source ) or Transistor PNP (max 100mA sink) or Relay SPDT 0.5A @ 240 VAC |
| Switching Logic | N.C. or N.O. Software selectable. |
| Isolation | 500 VDC Input / Output ( between probe and output signal ) |
| Electrical Connection | Micro-DC male plug or cable only |
Teflon ® is a registered trademark of E.I. du Pont de Nemours and Company.
1. Max. error on complete span. Error at calibration point ≤ 0.1 % of Span.
2. Max. error on complete calibrated span. Error at calibration points ≤ 0.1 % of Span.
3. Intempco sanitary sensors bearing the 3-A symbol meet the requirements of 3-A Sanitary Standards for Sensors and Sensor Fittings and Connections,
Number 74-03, with some exceptions to section D10 for heat sterilization systems . Intempco sensors meet the requirements of section D10.1 and D10.1.1
for sterilization of the product contact surfaces, with exception made for section D10.1.2 and D10.1.3. Intempco sensors do not have a steam or other
sterilization chamber surrounding the joint at the product contact surfaces between the fitting and the devices.
• Information furnished by Intempco is believed to be accurate and reliable. However, no responsibility is assumed by Intempco for its use.
• Specifications subject to change without notice
The DTG07 series Digital Temperature Gauges are a complete solution for most industrial temperature monitoring and temperature indicating applications.
Of high quality construction, these gauges features a bright and large 4-digit red LED display with an analog 4-20 mA output.
Based on Intempco’s patented MIST™ technology, they are designed for optimum accuracy and performance.
| Sensing Element | RTD, Type Pt100 Class A |
| Temperature Ranges | Customer re-scalable between –200 o C to 600 o C or –50 o C to 200 o C depending model. No re-calibration required. |
| Switching Ranges | Customer programmable between –200 o C to 600 o C or –50 o C to 200 o C depending model. |
| Hysteresis | Customer programmable, 1% of range by factory setting. |
| Accuracy | ± ( 0.25 o C + 0.40 % of reading ) max. with default calibration. ± ( 0.10 o C + 0.20 % of reading ) max. with one-point factory or customer calibration. |
| Open circuit detection | Upscale ( 22 mA ) or Downscale ( 2.5 mA ) current output. Error message on LED display. |
| Warm-up | 30 seconds. |
| Response Time | 0.5 sec to 30 sec ( software selectable ) |
| Display | 4-DIGITS LED, decimal point selectable by software. |
| Display resolution | ± 0.02 % F.S. ±1 DIGIT |
| RFI effect | 1 % or less typical |
| Temp. Effect | < 0.01 % FS/ o C |
| Ambient Temp. Range | – 40 o C to 80 o C ( -40 o F to 176 o F ) |
| Storage Temp. Range | – 50 o C to 85 o C ( -58 o F to 185 o F ) |
| Max. Pressure | 500 PSIG ( on probe ) |
| Housing Material | Stainless steel 316 |
| Probe Material | Stainless steel 316 standard |
| Cable Materials | PVC, Teflon®, Silicone, SS armored Teflon® |
| Environmental Protection | NEMA 4/IP 65 |
| ELE CTRICAL | |
| Power Supply | 9-36 VDC, polarity protected |
| Supply effect | 0.005 %/V |
| Power consumption | 15 mA @ 24 VDC + output current – 950 mW max. 20 mA @ 24 VDC for PNP output – 500 mW max. 20 mA @ 24 VDC + sourcing current for NPN output 50 mA @ 24 VDC for Relay Output – 1200 mW max. |
| Current Output | 4-20 mA (3 wires configuration) linear to temperature. |
| Max load on current output | ( Vsupply-9V )/ 20 mA, Ohms |
| Switching Output | Transistor NPN ( max 100 mA source ) or Transistor PNP (max 100mA sink) or Relay SPDT 0.5A @ 240 VAC |
| Switching Logic | N.C. or N.O. Software selectable. |
| Isolation | 500 VDC Input / Output ( between probe and output signal ) |
| Electrical Connection | Micro-DC male plug or cable only |
Teflon ® is a registered trademark of E.I. du Pont de Nemours and Company.
1. Max. error on complete span. Error at calibration point ≤ 0.1 % of Span.
2. Max. error on complete calibrated span. Error at calibration points ≤ 0.1 % of Span.
3. Intempco sanitary sensors bearing the 3-A symbol meet the requirements of 3-A Sanitary Standards for Sensors and Sensor Fittings and Connections,
Number 74-03, with some exceptions to section D10 for heat sterilization systems . Intempco sensors meet the requirements of section D10.1 and D10.1.1
for sterilization of the product contact surfaces, with exception made for section D10.1.2 and D10.1.3. Intempco sensors do not have a steam or other
sterilization chamber surrounding the joint at the product contact surfaces between the fitting and the devices.
• Information furnished by Intempco is believed to be accurate and reliable. However, no responsibility is assumed by Intempco for its use.
• Specifications subject to change without notice
WJF Instrumentation Ltd.
#5 3610 – 29th Street N.E.
Calgary, Alberta
Canada
T1Y 5Z7
Calgary Head Office
Toll-Free: (877) 291-5572
Standard: (403) 291-5570
Ontario & Maritimes Sales:
Toll-Free (877) 291-5572
